Below you will be given an overview of all selection lists that apply for certain attributes, dependent on any tag being used.
functiontemplate: characteristics (Characteristic)
Note:
For cables / connections this is the potential type.
Internal value |
Display value |
---|---|
|
Undefined |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
functiontemplate: terminalfunction (Terminal category)
Note:
This property is only available for terminals.
Internal value |
Display value |
---|---|
|
Feed-through terminal |
|
Isolating terminal |
|
Switching terminal |
|
Diode terminal |
|
Fused terminal |
|
Resistance terminal |
|
Thermocouple terminal |
functiontemplate: plcbussystem (Bus system)
Internal value |
Display value |
---|---|
|
Other bus systems |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Local bus: Rack / module |
|
|
|
|
|
|
|
|
|
|
|
Local bus: Extension |
|
|
|
|
|
CC Link |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
RIO/DIO bus |
|
MDI I/O bus |
|
|
|
CC-Link IE |
|
Modbus TCP |
|
|
|
|
|
|
|
CC-Link IE Control |
|
CC-Link IE Field |
functiontemplate: idx1 (Item IDs (3D) for function definition "Enclosure > Frame profile")
Internal value |
Display value |
---|---|
|
Frame profile vertical left front |
|
Frame profile vertical left back |
|
Frame profile vertical right back |
|
Frame profile vertical right front |
|
Frame profile horizontal |
|
Frame profile - general |
|
Frame profile horizontal cover |
|
Frame profile horizontal floor |
functiontemplate: idx1 (Item IDs (3D) for function definition "Housing > Panel")
Internal value |
Display value |
---|---|
|
Side panel left |
|
Side panel right |
|
Floor |
|
Roof plate |
|
Rear panel |
|
Panel general |
functiontemplate: idx1 (Item IDs (3D) for function definition "Housing > Door")
Internal value |
Display value |
---|---|
|
Door |
|
Door left |
|
Door right |
functiontemplate: idx1 (Item IDs (3D) for function definition "Area definition > Mounting area > Mounting surface")
Internal value |
Display value |
---|---|
|
Mounting surface |
|
Mounting panel front |
|
Mounting panel back |
|
Door outside |
|
Door inside |
|
Door left outside |
|
Door left inside |
|
Door right outside |
|
Door right inside |
|
Side panel left outside |
|
Side panel left inside |
|
Side panel right outside |
|
Side panel right inside |
|
Cover outside |
|
Cover inside |
|
Floor outside |
|
Floor inside |
|
Rear panel outside |
|
Rear panel inside |
|
Panel outside |
|
Panel inside |
|
Profile level |
|
Profile level left inside |
|
Profile level right inside |
|
Profile level back inside |
|
Profile level front inside |
|
Profile level floor inside |
|
Profile level cover inside |
|
Profile level left outside |
|
Profile level right outside |
|
Profile level back outside |
|
Profile level front outside |
|
Floor sheet inside |
|
Floor sheet outside |
|
Profile level left inside vertical |
|
Profile level right inside vertical |
|
Profile level back inside vertical |
|
Profile level front inside vertical |
|
Mounting surface NC front |
|
Area floor sheets |
|
Profile level door |
|
Profile level door left |
|
Profile level door right |
|
Flange plate inside |
|
Flange plate outside |
|
19-inch profile level |
|
Mounting surface Copper |
functiontemplate: idx1 (Item IDs (3D) for function definition "NC machining > Free drill hole > Rectangle")
Internal value |
Display value |
---|---|
|
Rectangle square |
|
Rectangle rounded |
|
Rectangle chamfered |
part: P_ARTICLE_MOUNTINGSITE (Mounting surface)
Internal value |
Display value |
---|---|
|
Undefined |
|
Mounting panel |
|
Pivoting frame |
|
Door |
|
Side section |
|
Top cover |
part: P_ARTICLE_HINGEPOSITION (Door: hinge)
Internal value |
Display value |
---|---|
|
Left |
|
Right |
variant: P_ARTICLE_WIRECROSSSECTION_UNIT (Unit for connection cross-section / diameter)
Internal value |
Display value |
---|---|
|
As in project |
|
|
|
|
|
|
|
|
|
|
|
|
|
Zoll |
|
|
|
inch |
|
|
|
|
|
µm2 |
terminal: P_PART_TERMINAL_DIRECTION
(Routing direction)
Internal value |
Display value |
---|---|
|
Automatic |
|
Up |
|
Down |
|
Left |
|
Right |
terminal: P_PART_TERMINAL_TYPEDEFAULT
(Wire termination processing (EPLAN Cabinet)) / terminalPosition: type (Wire termination processing)
The following values are default values and can be freely defined via the following setting:
Internal value |
Display value |
---|---|
|
Undefined |
|
Cut |
|
Strip |
|
Crimp |
|
Other |
Other values can be freely specified in the "
The internal value has to be set in the
The display value is a multilingual text.
terminal: P_PART_TERMINAL_TYPEOFTERMINAL_DEFAULT (Connection category) / terminalPosition: typeofterminal (Connection category)
Internal value |
Display value |
---|---|
|
Undefined |
|
Screw clamp connection single |
|
Screw clamp connection double |
|
Cage clamp connection |
|
Insulation-displacement connection |
|
Screw-type connection (Ring or U cable lug) |
|
Ferrule connection (cable lug) |
|
Plug connection |
|
Solder connection |
|
Plug-in connection (Fluid) |
|
Nipple |
|
Internal thread |
|
External thread |
|
Compression nut |
|
Compression fitting |
blockingSurfacePosition: type (Type)
Internal value |
Display value |
---|---|
|
Restricted placing area |
|
Restricted drilling area |
mountingPanelPosition: location (Mounting location)
Internal value |
Display value |
---|---|
|
Back |
|
Left |
|
Right |
drillingPosition: type (Drill type)
Internal value |
Display value |
---|---|
|
Undefined |
|
Drill |
|
Thread |
|
Rectangular |
|
Slotted hole |
|
Hexagon |
|
Octagon |
|
User-defined outline |
drillingPosition: subtype (Subtype)
Internal value |
Display value |
---|---|
|
Undefined |
|
Square |
|
Chamfered |
|
Rounded |
terminalPosition: direction (Routing direction)
Internal value |
Display value |
---|---|
|
Automatic |
|
Up |
|
Down |
|
Left |
|
Right |
address: class (Type)
Internal value |
Display value |
---|---|
|
Customer |
|
Manufacturer / supplier |